Technical product documentation (TPD). General principles of representation. Part 71, Simplified representation for mechanical engineering drawings / ISO.
Saved in:
Edition: | First edition |
---|---|
Published: |
[Geneva], Switzerland :
ISO,
[2010]
©2010 |
Corporate Authors: | |
Series: | International standard ;
ISO 128-71:2010. |
Subjects: | |
Format: | Book |
MARC
LEADER | 00000nam a2200000 i 4500 | ||
---|---|---|---|
001 | 3294859 | ||
005 | 20230712132700.0 | ||
008 | 230712s2010 enka u 000 0 eng d | ||
097 | |3 Bib#: |a 3294859 | ||
040 | |a CU |b eng |e rda |c CU | ||
110 | 2 | |a International Organization for Standardization. |e issuing body, |e author. | |
245 | 1 | 0 | |a Technical product documentation (TPD). General principles of representation. |n Part 71, |p Simplified representation for mechanical engineering drawings / |c ISO. |
246 | 3 | 0 | |a General principles of representation. |n Part 71, |p Simplified representation for mechanical engineering drawings |
246 | 3 | 0 | |a Simplified representation for mechanical engineering drawings |
246 | 1 | 3 | |i At head of title: |a Technical specification |
246 | 3 | 3 | |a ISO/TS 128-71:2010(E) |
246 | 3 | 3 | |a ISO/TS 128-71 |
246 | 3 | 3 | |a ISO/TS 128 |
250 | |a First edition | ||
264 | 4 | |a [Geneva], Switzerland : |b ISO, |c [2010] | |
264 | 4 | |c ©2010 | |
300 | |a vi, 10 pages : |b illustrations ; |c 30 cm | ||
336 | |a text |2 rdacontent | ||
337 | |a unmediated |2 rdamedia | ||
338 | |a volume |2 rdacarrier | ||
490 | 1 | |a International standard ; |v ISO 128-71:2010 | |
500 | |a Cover title. | ||
500 | |a "ICS 01.100.20"--Back cover. | ||
500 | |a "Reference number ISO/TS 128-71:2010(E)." | ||
500 | |a "The ISO 128-71 was prepared by Technical Committee ISO/TS 10, Technical product documentation, Subcommittee SC 6, Mechanical engineering documentation"--Foreword. | ||
500 | |a "This part of the ISO 128 has been established to specify rules and guidance for the use of the simplified representation on mechanical engineering drawings"--Introduction. | ||
520 | 0 | |a "The provisions of this part of the ISO 128 are based on those of ISO 128-30, ISO 128-40, ISO 128-50, ISO 129-1 (Technical drawings - Indication of dimensions and tolerances - Part 1:General principles) and ISO 6411 (Technical drawings - Simplified representation of centre holes)"--Scope page 1. | |
650 | 0 | |a Mechanical drawing |x Standards. | |
710 | 2 | |a Technical Committee ISO/TS 10, Technical product documentation |b Subcommittee SC 6, Mechanical engineering documentation, |e author. | |
830 | 0 | |a International standard ; |v ISO 128-71:2010. | |
945 | |b DO NOT SET |c Manual | ||
991 | |a 2023-07-12 | ||
992 | |a Created by nimo, 12/07/2023. Updated by nimo, 12/07/2023. | ||
999 | f | f | |i 585f1270-fbaa-5001-adae-038e43108b69 |s 16b2a6e2-0e3b-5f10-a488-22e450d15a97 |t 0 |
952 | f | f | |p 3 day |a University Of Canterbury |b UC Libraries |c EPS Library |d EPS Library, Level 1, Standards Collection |t 0 |e ISO/TS 128-71:2010(E) |h Local |i Standard |m AU20517181B |